Fence installation around Hammond typically costs $10 to $60 per linear foot installed for the common fence types, and ornamental steel or iron runs $30 to $100 or more. A 6 ft pressure-treated pine privacy fence typically costs $15 to $45 per foot, vinyl privacy $20 to $60 and residential chain link $10 to $30. Gates and removal of an old fence are priced on top.
Palisades Hammond Fence installs, replaces and repairs residential and commercial fences in Hammond and across Tangipahoa Parish, western St. Tammany and eastern Livingston Parish, with installation carried out by licensed and insured fence contractors. The figures on this page are typical Hammond-area ranges for budgeting, not quotes and not a company rate.
What follows explains what sits inside them, why two yards of the same length can price differently, and which local costs have a public figure you can check yourself. For a number tied to your own length and options, the fence cost estimator gives a range without a phone call.
Typical installed ranges by fence type
These ranges cover materials and labor together on a normal residential lot with workable access. They are regional budgeting ranges, not company prices, and a written scope is what turns one into a number for your yard.
| Fence type | Typical installed range | Where a job lands in it |
|---|---|---|
| Wood privacy, 6 ft pressure-treated pine | $15 to $45 per linear foot | Flat, open runs with one gate sit low; shadowbox styles, wet or root-filled ground and tear-out push it up |
| Wood privacy, 6 ft cedar | $22 to $55 per linear foot | Cedar boards cost more than pine; the posts can still be treated pine or steel |
| Vinyl privacy, 6 ft | $20 to $60 per linear foot | Heavier profiles, decorative caps and aluminum post stiffeners raise it |
| Chain link, 4 to 6 ft galvanized residential | $10 to $30 per linear foot | 4 ft galvanized sits low; 6 ft, black vinyl-coated fabric and privacy slats sit at or above the top |
| Aluminum ornamental | $25 to $55 per linear foot | Height, picket spacing, slope and gate count |
| Steel or wrought iron ornamental | $30 to $100 or more per linear foot | Standard panels start near the bottom; custom scrollwork, columns and on-site welding open the top |
| Aluminum pool barrier | $25 to $55 per linear foot | Barrier rules, self-closing gate hardware and the number of gates |
| Standard walk gate | $150 to $600 each | Width, frame material, hinges, latch and the size of the gate posts |
| Old fence tear-out and haul-away | $2 to $8 per linear foot | Posts set in concrete and long carries cost more to remove |
The spread inside each row is real. A straight 6 ft pine run across an open backyard, with no old fence to remove and dry ground at the post holes, is a different job from the same length that crosses a drainage swale, turns three corners, dodges a live oak’s roots and meets the house at a gate.
The second needs more posts, more cuts, deeper or wider footings and more hours, which is where the top of the band comes from. The privacy fence cost guide goes deeper on wood and vinyl privacy styles.
What moves a price within the range
Footage and material set the base, but they rarely explain the gap between two quotes. The drivers below are the ones fence contractors price, with the local reason each one moves around Hammond.
| Driver | Why it changes the price | What it looks like around Hammond |
|---|---|---|
| Linear footage | Sets the post count, the material order and most of the labor | Per-foot cost usually falls a little on long, straight runs because setup is spread over more feet |
| Fence height | Taller fences need longer posts, deeper footings and more material | Hammond allows up to 4 ft in front of the house and up to 8 ft from the front line back, measured from the lower side of the fence |
| Material and system | Sets the base rate in the table above | Front-yard fences in Hammond must be wood, metal other than chain link, or masonry |
| Post spacing and depth | Closer spacing and deeper footings add posts, concrete and digging time | A solid 6 ft face catches far more wind than an open fence, so it needs more post |
| Soil and water | Wet holes cave, hold water and need gravel, more concrete or a different post | The soils mapped around Hammond are mostly poorly drained silt loams, with a seasonal water table near the surface (USDA NRCS) |
| Frost depth | Deep frost lines force deeper posts in cold climates | Not a driver here: Hammond averages about 31 nights a year at or below freezing (NOAA), but freezes are brief, so depth follows wind, height and soil |
| Slope | Racking or stepping panels takes more cuts, longer posts and layout time | Mostly flat ground, but ditch banks and raised beds still create grade changes |
| Gates | Each gate needs heavier posts, hardware and adjustment | Walk gates are priced per gate; driveway gates are scoped separately |
| Tear-out and disposal | Old posts, concrete and panels come out and are hauled away | $2 to $8 per foot, more where old posts sit in concrete |
| Access | Long hand carries slow every step | Narrow side yards, ditches along the street and soft lawns after rain limit equipment |
| Property line or survey | An unclear line can need a surveyor before layout | Hammond approves the fence location from a survey or parcel map |
| HOA or permit requirements | Approval steps, required styles and drawings add time | Recorded subdivision restrictions can be stricter than the city code |
| Pool-barrier requirements | Height, gap limits and self-closing gates narrow the product choice | See the pool fence requirements guide |
| Decorative caps and trim | Cap rails, post caps and trim boards add material and labor | Most often chosen on vinyl and on front-yard picket and iron fences |
| Staining or painting | A separate labor step and product | About 64 inches of rain a year and long, hot summers wear finishes quickly |
| Welding and fabrication | Custom iron, on-site welds and coating take shop and field time | Mostly ornamental steel, iron gates and pipe fencing |
| Tree and root conflicts | Posts shift or are hand-dug around roots | Matters wherever a fence line runs past mature oaks or pines |
| Corrosion exposure | Coatings and hardware rated for wet conditions cost more | Flood-prone and low lots favor galvanized or coated hardware and posts |
The soil row matters more here than in most places. At half the points sampled around Hammond in the USDA soil survey, the seasonal high water table sits about 23 cm (roughly 9 inches) or less below the surface, and the shallowest reading was 13 cm. A post hole dug in that season can fill with water before the concrete goes in, which is why wet-ground methods, and sometimes a different post, show up in the price. The wet clay soil guide explains those methods.
What’s inside a Hammond fence price
A contractor’s price bundles labor, materials, permits, insurance and overhead. Several parts have public figures you can check, and the rest are scope items to confirm in writing.
| Part of the price | What sets it | Local figure |
|---|---|---|
| Installer labor | Local wages, hours on site, crew size | BLS does not publish a fence-erector wage for the Hammond metro. Louisiana fence erectors earn a mean $19.92 an hour against $24.29 nationally, about 18% lower (BLS OEWS, fence erectors). Construction laborers in the Hammond metro average $19.63 an hour against $25.02 nationally, about 22% lower (BLS OEWS, construction laborers) |
| Materials | Species or system, height, gates, hardware | No public local price list; scope to check on the quote’s material list |
| Sales tax on materials | State and local rates | Louisiana’s state sales tax rate is 5% (Louisiana Department of Revenue); parish and city sales taxes add to it and vary by jurisdiction |
| Code-required design | Hammond Unified Development Code 4.1.8 | Front-yard fences 4 ft maximum and not chain link or wire; wire fences on galvanized pipe posts at least 1.5 in across and no more than 7 ft apart; wood must be weatherproofed (City of Hammond UDC) |
| City fence permit | Hammond fee schedule, UDC Appendix H | $10 residential, $50 commercial; the fee doubles if work begins before the permit is issued, and the City can order work removed |
| State per-permit fee | LUCCC Resolution 2026-01, adopted July 7, 2026 under Act 881 | A $10 state fee per permit issued by a local government (LUCCC); whether it is added to a fence permit is confirmed with the permit office |
| Contractor licensing and insurance | LSLBC thresholds and Act 757 | Home improvement registration for residential jobs over $7,500 (LSLBC); minimum general liability coverage for residential and home improvement applicants rose to $500,000 effective August 1, 2026 |
| City contractor license | Hammond fee schedule | $150 for a contractor not licensed by the state, $75 to renew; an overhead cost, not a homeowner fee |
| Historic district review | Hammond Historic District Commission; Hyer-Cate overlay | A street-facing fence in the historic district needs commission review on top of the permit; no fee figure found, so treat it as time and scope to check |
| Utility locate | Louisiana R.S. 40:1749.13 | Louisiana 811 must be notified at least 48 and no more than 120 hours before digging, excluding weekends and holidays; it sets the schedule more than the price |
| Survey | Louisiana Civil Code arts. 784-792 | No public price; when neighbors fix a boundary outside court, the cost is split equally unless they agree otherwise |
| Tear-out and debris | How the old fence was set | Covered by the $2 to $8 per foot removal range |
| Lawn, bed, irrigation and ditch restoration | What the fence line crosses | No public figure; confirm who restores what |
A wage is not a billing rate: an installed price also carries materials, equipment, vehicles, insurance, licensing, disposal and overhead. The BLS figures explain direction rather than a per-hour charge. Labor is one input where the Hammond area runs below the national level, and the higher insurance minimum under Act 757 is one that pushes the other way.
Permit fees in Hammond and nearby
The fence permit guide explains when each authority requires a permit and what the application needs. For budgeting, here is what is known about the fee in each place.
| Where the property is | Permit rule | Fee |
|---|---|---|
| City of Hammond | A fence permit is required before any fence goes in, with the design and location approved from a survey or parcel map | $10 residential, $50 commercial; doubled if work starts first. Permits: (985) 277-5655 |
| City of Covington | Fence Permit Application with a dimensioned drawing of heights, locations and property lines | $5 (City of Covington) |
| City of Mandeville | Height and location limits set in the city’s land use code | Fee and current text confirmed per address; see the Mandeville page |
| Unincorporated Tangipahoa Parish | Not verified | Confirmed per address |
| Ponchatoula, Livingston Parish and other towns | Each has its own permit office; fence rules not verified | Confirmed per address |
Two Hammond rules can change the design and therefore the price. Within 30 ft of a street intersection, nothing more than 3 ft high may stand, so a corner-lot privacy fence often steps down or starts back from the corner. And inside the Hammond Historic District, a fence facing a street or alley needs Historic District Commission review before work begins. In Covington, the Covington page covers the historic district guidelines.
Work priced by scope: what drives the price
Some work has no dependable per-foot range for this area, because the scope varies too much between properties. These items are priced from a site visit, and the drivers below are what move them.
Board-on-board and cypress
A board-on-board fence uses roughly half again as many boards per foot as a standard privacy fence, looks finished from both sides, and puts a heavier, fully solid face on the posts and rails in wind. It sits above standard privacy in the same material. Cypress depends on what grade and board width are available locally, plus the finish.
Farm, horse and pipe fencing
Farm fence prices turn on wire type and gauge, post type and spacing, braced corners and ends, the length of the run, wet ground, clearing the line and the number of field gates. Horse fencing adds board count or no-climb wire spec, a top rail or board, and paint. Pipe fence depends on pipe diameter and wall, welding, post setting depth and paint. The farm fence cost guide covers these in more detail.
Driveway, sliding and automatic gates
A double drive gate is priced by width, material, frame bracing, hinge posts and the drop rod or latch. A sliding gate adds the choice between a track and a cantilever frame. An automatic gate brings in the gate’s weight, the operator, the power run from the house, access controls and safety devices. The gate cost guide walks through each.
Repairs, post replacement and staining
Fence repair and post replacement depend on the post material, whether an old concrete footing has to come out, whether the boards or panels can be matched, access and the contractor’s minimum charge. Fence staining depends on one face or two, height, cleaning or stripping, the product, access and the age of the wood. Black vinyl-coated and commercial chain link are scoped by coating, fabric gauge, post size, height, barbed-wire arms, gate width and access control.
Illustrative budgets
These examples use only the ranges above. They are illustrative arithmetic, not quotes.
| Example | How it adds up | Illustrative total |
|---|---|---|
| 150 ft of 6 ft pine privacy, one walk gate | $2,250 to $6,750 for the fence plus $150 to $600 for the gate | $2,400 to $7,350 |
| Same fence, replacing an old wood fence | Add $300 to $1,200 for 150 ft of tear-out | $2,700 to $8,550 |
| 200 ft of 6 ft vinyl privacy, two walk gates | $4,000 to $12,000 for the fence plus $300 to $1,200 for the gates | $4,300 to $13,200 |
| 120 ft of 4 ft residential chain link, one walk gate | $1,200 to $3,600 for the fence plus $150 to $600 for the gate | $1,350 to $4,200 |
| 100 ft of aluminum pool barrier | $2,500 to $5,500 for the fence; the self-closing gate is priced by its hardware | $2,500 to $5,500 plus the gate |
Inside Hammond city limits, add the $10 residential permit. A run across wet, root-filled ground, a long hand carry or extra corners moves a job toward the top of each range; a straight, dry, open run sits lower. The second example also shows why the LSLBC threshold matters: at the top of its range, that job is over $7,500.
Rebates and incentives
No rebate, grant or tax credit for homeowner fencing was found for Hammond, Tangipahoa Parish or the neighboring parishes. The Louisiana Fortify Homes Program, run by the Louisiana Department of Insurance, helps owners upgrade roofs to the FORTIFIED standard; it does not cover fences, even storm-hardened ones. Agricultural producers working under a USDA NRCS conservation plan can ask their local NRCS office whether conservation fencing qualifies, but that is a farm program, not a homeowner one. Plan the budget without an incentive.
Before you compare quotes
Line the quotes up item by item:
- footage and height
- post material, size and spacing
- how posts are set in wet ground
- the number and width of gates and their hardware
- tear-out and haul-away
- the permit and who pulls it
- 811 scheduling and cleanup
If the fence sits on a shared line, Louisiana Civil Code article 685 presumes a boundary fence is common to both owners, which can affect who pays; the Louisiana fence laws guide explains how.
If wind is the worry, the wind-resistant fence page shows how post and rail choices change for storms, and those choices show up in the price. If you are replacing a failing fence, the fence replacement page explains how the old line is assessed first.
When you have a rough footage and a material in mind, call Palisades Hammond Fence at (985) 866-3827 or request an estimate to turn a range into a written scope for your property.
Get a fence price for your Hammond-area property
Send the footage, height and material you have in mind, plus any gates and an old fence to remove, to start an estimate.
